Issues »  Volume 16, Issue 1

Influence of Different Types of Deformation on the Physical and Mechanical Properties of H.C.P. and F.C.C. Metals and Alloys

V. V. Kalinovskyy, M. B. Lazareva, D. G. Malykhin, O. V. Mats, V. S. Okovit, V. I. Sokolenko, L. O. Chirkina

National Science Center Kharkov Institute of Physics and Technology, NAS of Ukraine, 1 Akademicheskaya Str., 61108 Kharkov, Ukraine

Received: 22.12.2014. Download: PDF

We present an overview of the influence of different types of deformation with different stress distributions (rolling, drawing, deformation by hydrostatic compression method of quasi-hydroextrusion (QHE) and sequential combination of drawing and QHE at 77 K and 300 K on different physical and mechanical properties of metals and alloys: h.c.p. (Hf, Zr, Ti) and f.c.c. (Al–Mg–Li, 06Х16Н15М3B austenitic steel). The differences in the level of strength, the rate of accumulation of deformation defects, and the anisotropy of their distribution within the bulk of deformed material after drawing, rolling, and QHE are revealed. For the 06Kh16N15M3B steel as an example, we established the reasonability to use a sequence of a combined deformation by drawing with quasi-hydroextrusion for a significant increase in the strength of steel, than that after each individual type of deformation. We revealed the 25%-lowering of the stacking fault energy of titanium, i.e. splitting of dislocations due to the deformation under the uniform compression at 77 K and 300 K. The abnormal increase in shear modulus after the deformation of titanium by hydrostatic compression is revealed. Finally, we discuss the mechanisms of the influences of different types of deformation on mechanical properties of metals and alloys.

Keywords: rolling, drawing, quasi-hydrostatic extrusion, structure, stacking defect.

PACS: 06.60.Vz, 62.20.F-, 62.20.Qp, 62.40+i, 62.50.-p, 81.40.Ef, 81.40.Lm

DOI: https://doi.org/10.15407/ufm.16.01.061

Citation: V. V. Kalinovskyy, M. B. Lazareva, D. G. Malykhin, O. V. Mats, V. S. Okovit, V. I. Sokolenko, and L. O. Chirkina, Influence of Different Types of Deformation on the Physical and Mechanical Properties of H.C.P. and F.C.C. Metals and Alloys, Usp. Fiz. Met., 16, No. 1: 61—84 (2015) (in Russian), doi: 10.15407/ufm.16.01.061

References (33)  
  1. R. Z. Valiev and I. V. Aleksandrov, Nanostrukturnye Materialy, Poluchennye Intensivnoy Plasticheskoy Deformatsiey [Nanostructured Materials Obtained by Intensive Plastic Deformation] (Moscow: Logos: 2000) (in Russian).
  2. N. A. Enikeev and M. Yu. Murashkin, 'Vysokie Davleniya—2012. Fundamental'nye i Prikladnye Aspekty' (Sept. 23–27, 2012, Sudak), p. 125 (in Russian).
  3. M. B. Lazareva, V. S. Okovit, L. A. Chirkina, M. P. Starolat, V. V. Kalinovskiy, I. F. Borisova, V. I. Sokolenko, and K. V. Kovtun, Voprosy Atomnoy Nauki i Tekhniki. Seriya: Vakuum, Chistye Materialy, Sverkhprovodniki [Problems of Atomic Science and Technology], No. 6 (18): 32 (2009) (in Russian).
  4. M. A. Tikhonovskiy, I. F. Kislyak, O. I. Volchok, T. Yu. Rudycheva, N. V. Kamyshanchenko, I. S. Nikulin, Fizika i Tekhnika Vysokikh Davleniy, 18, No. 4: 96 (2008) (in Russian).
  5. S. K. Panigrahi and R. Jayaganathan, Mat. Sci. Eng. A, 480: 299 (2008). Crossref
  6. I. P. Semenova, A. V. Polyakov, G. I. Raab, T. S. Lou, and R. Z. Valiev, 'Vysokie Davleniya—2012. Fundamental'nye i Prikladnye Aspekty' (Sept. 23–27, 2012, Sudak), p. 126 (in Russian).
  7. V. V. Malashenko and T. I. Malashenko, 'Vysokie Davleniya—2012. Fundamental'nye i Prikladnye Aspekty' (Sept. 23–27, 2012, Sudak), p.156 (in Russian).
  8. P. A. Khaimovich, Handbook of Mechanical Nanostructuring (Ed. M. Aliofkhazraei) (Germany: Wiley-VCH Verlag GmbH & Co. KGaA: 2015).
  9. V. V. Malashenko and N. V. Belykh, Fiz. Tverdogo Tela, 55, Iss. 3: 504 (2013) (in Russian).
  10. I. A. Gindin, V. I. Kovalenko, V. S. Okovit, Ya. D. Starodubov, and L. A. Chirkina, Zavod. Lab., No. 11: 1397 (1970) (in Russian).
  11. A. Granato and K. Lücke, Ul'trazvukovye Metody Issledovaniya Dislokatsiy [Ultrasonic Methods of Study of Dislocations] (Moscow: Izd. Inostrannoy Literatury: 1963), p. 25 (Russian translation).
  12. J. Swartz and J. Weertman, Ul'trazvukovye Metody Issledovaniya Dislokatsiy [Ultrasonic Methods of Study of Dislocations] (Moscow: Izd. Inostrannoy Literatury: 1963), p. 58 (Russian translation).
  13. M. A. Krishtall, S. A. Golovin, and S. I. Arkhangel'skiy, Vnutrennee Trenie v Metallakh i Splavakh [Internal Friction in Metals and Alloys] (Moscow: Nauka: 1966), p. 101 (in Russian).
  14. M. A. Krishtall and S. A. Golovin, Relaksatsionnye Yavleniya v Tverdykh Telakh [Relaxation Phenomena in Solids] (Moscow: Metallurgiya: 1968), p. 417 (in Russian).
  15. A. Novik and B. Berri, Relaksatsionnye Yavleniya v Kristallakh [Relaxation Phenomena in Crystals] (Moscow: Atomizdat: 1975), p. 316 (in Russian).
  16. A. H. Cottrell, Dislocations and Plastic Flow in Crystals (New York: Oxford Univ. Press: 1953).
  17. K. V. Kutniy, O. I. Volchok, I. F. Kislyak, M. A. Tikhonovsky, and G. E. Storozhilov, Mat.-wiss. u. Werkstofftech., 42, No. 2: 114 (2011). Crossref
  18. O. V. Chernyi, G. E. Storozhilov, N. F. Andrievskaya, V. O. Ilichova, Ya. D. Starodubov, O. I. Volchok, L. A. Chirkina, M. B. Lazareva, and V. S. Okovit, IEEE Trans. Appl. Supercond., 15, No. 2: 3502 (2005). Crossref
  19. I. M. Neklyudov, O. I. Volchok, V. V. Kalinovskiy, V. S. Okovit, V. I. Sokolenko, P. A. Haymovich, N. A. Chernyak, and L. A. Chirkina, Voprosy Atomnoy Nauki i Tekhniki. Seriya: Vakuum, Chistye Materialy, Sverkhprovodniki [Problems of Atomic Science and Technology], No. 1 (17): 108 (2008) (in Russian).
  20. L. A. Chirkina, M. B. Lazareva, V. S. Okovit, V. I. Sokolenko, P. A. Khaymovich, V. V. Kalinovskiy, V. P. Poyda, V. V. Bryukhovetskiy, and A. V. Poyda, Vestnik Kharkiv Nat. Univ. Seriya 'Fizika', 16, No. 1: 75 (2012) (in Russian).
  21. M. B. Lazareva, V. S. Okovit, M. P. Starolat, V. I. Sokolenko, V. V. Kalinovskiy, L. A. Chirkina, A. A. Vasil'ev, and K. V. Kovtun, Voprosy Atomnoy Nauki i Tekhniki. Seriya: Vakuum, Chistye Materialy, Sverkhprovodniki [Problems of Atomic Science and Technology], No. 6 (19): 30 (2011) (in Russian).
  22. I. A. Yuhvets, Volochil'noe Proizvodstvo [Wire Drawing Manufacture] (Moscow: Metallurgiya: 1965) (in Russian).
  23. V. V. Kalinovskiy, L. A. Chirkina, M. B. Lazareva, V. S. Okovit, V. I. Sokolenko, P. A. Haymovich, and A. V. Mac, Fiz. i Tekhn. Vys. Davleniy, 23, No. 2: 103 (2013) (in Russian).
  24. L. A. Chirkina, M. B. Lazareva, V. I. Sokolenko, V. V. Kalinowski, P. A. Khaimovich, and V. S. Okovit, Voprosy Atomnoy Nauki i Tekhniki. Seriya: Vakuum, Chistye Materialy, Sverkhprovodniki [Problems of Atomic Science and Technology], No. 1 (89): 115 (2014).
  25. R. Berner and G. Kronmüeller, Plastische Verformung von Einkristallen (Berlin: Springer-Verlag: 1965). Crossref
  26. M. A. Shtremel, Prochnost' Splavov. Part 1. Defekty Reshetki [Strength of Alloys. Part 1. Defects of Lattice] (Moscow: MISiS: 1999) (in Russian).
  27. A. E. Smith, Materials Forum, 31: 71 (2007).
  28. A. M. Kosevich, Dislokatsii v Teorii Uprugosti [Dislocations in the Theory of Elasticity] (Kiev: Naukova Dumka: 1978) (in Russian).
  29. A. A. Galkin, V. V. Tokiy, and V. I. Zaytsev, DAN AN SSSR, 204, No. 2: 313 (1972) (in Russian).
  30. V. I. Zaytsev, Fizika Plastichnosti Gidrostaticheski Szhatykh Kristallov [Physics of Plasticity of Hydrostatically Compressed Crystals] (Kiev: Naukova Dumka: 1983) (in Russian).
  31. M. J. Zehetbauer, H. P. Stuwe, V. Vorhauer, E. Schafler, and J. Kohout, Adv. Eng. Mat., 5, No. 3: 330 (2003). Crossref
  32. E. D. Martynov, V. I. Trefilov, S. A. Firstov, and B. N. Beresnev, Yu. N. Ryabinin, DAN SSSR, 176, No. 6: 1276 (1967) (in Russian).
  33. I. A. Gindin,Ya. D. Starodubov, M. L. Starolat, and P. A. Khaimovich, Fiz. Met. i Metallovedenie, 48, Iss. 5: 1004 (1979) (in Russian).

© 2013–2018 "G.V. Kurdyumov Institute for Metal Physics"